阿克苏油漆施工工艺设计-I6

《阿克苏油漆施工工艺设计-I6》由会员分享，可在线阅读，更多相关《阿克苏油漆施工工艺设计-I6（14页珍藏版）》请在文档大全上搜索。

1、.阿克苏诺贝尔防护涂料（苏州）有限公司Akzo Nobel International Paint（Suzhou）Co., Ltd.项目名称PROJECT NAMEOEM ProjectANIP 文件编号页码 Page版次 REVANIP DOC. No.ANPC-TSDYRPWP0015文件编号ANPC-TSDYRPWPDOC. No.Paint Working Procedure ForInterseal 670HS01Issue for Approve说明日期编制审核批准日期审核批准版次 REVDatePRE DReviewApproveDateReviewApproveDescript

2、ionCoating Supplier涂料供应商Akzo Nobel International Paint (Suzhou) Co., ltd1. Scope前言教育资料.This PaintingTechnology Specification covers surface preparation and paintingspecification.Thisdocument isorganizedon basisofInternationalProtectiveCoatingsProductsData Sheets.It is composed of additional regulati

3、ons and the detail descriptions in the above documentsmentioned, and therefore is not to be the substitute of the approved specifications. Thespecification is prepared with the reference of the Project Contract Specification.本技术工艺涵盖了表面处理及涂料技术规格。文件根据阿克苏诺贝尔防护涂料产品手册制定的，不是取代任何该项目的规范文件，而是对它们补充说明或细节性描述。此外

4、，本文件服从于此项目合同技术规范中提到的要求。2. Standards, References, Definitions and Abbreviations标准和参考文献2.1 Abbreviations缩写SSPC The Society of Protective Coating美国防护涂料协会ASTM America Society for Testing and Materials美国试验和材料协会ISOInternational Standard Organization国际标准化组织DFTDry Film Thickness干膜厚度WFTWet Film Thickness湿膜厚度

5、2.2 Reference and Standards现行的参考和标准ISO 8501-1Preparationofsteelsubstratesbeforeapplicationofpaintsand relatedproducts - Visual assessment of surface cleanliness.表面清洁度目测法评估ISO 8502-3Preparationofsteelsubstratesbeforeapplicationofpaintsand relatedproducts -Test for the assessment of surface cleanlines

6、s- Assessment of duston steel surfaces prepared for painting, pressure sensitive tape method.表面清洁度测试评估准备涂漆的钢材表面灰尘评估压敏胶带法ISO 8503Preparationofsteelsubstratesbeforeapplicationofpaintsand relatedproducts - Surface roughness characteristics of blast cleaned substrates.喷射清理表面粗糙度特征ISO 11124Preparationofst

7、eelsubstratesbeforeapplicationofpaintsand relatedproducts - Specifications for metallic blast-cleaning abrasives - Part 2:Chilled-iron grit - Part 3: High-carbon cast-steel shot and grit油漆和相关产品施工前钢材表面处理 金属喷砂清洁磨料的规定ISO 11125Preparationofsteelsubstratesbeforeapplicationofpaintsand relatedproducts - Te

8、st methods for metallic blast-cleaning abrasives油漆和相关产品施工前钢材表面处理 金属喷砂清洁磨料测试方法ISO 11126Preparationofsteelsubstratesbeforeapplicationofpaintsand relatedproducts - Specifications for non-metallic blast-cleaning abrasives油漆和相关产品施工前钢材表面处理 非金属喷砂清洁磨料的规定ISO 11127Preparationofsteelsubstratesbeforeapplication

9、ofpaintsand relatedproducts - Test methods for non-metallic blast-cleaning abrasives教育资料.油漆和相关产品施工前钢材表面处理 非金属喷砂清洁磨料测试方法SSPC SP1Solvent Cleaning溶剂清洗SSPC SP10/ISO Sa 2.5Near White Blast Cleaning近白级喷射清理SSPC SP3/ISO St3Power Tool Cleaning动力工具清理SSPC PA 2Measurement of Dry Film Thickness干膜厚度测量方法ISO 2808Me

10、asurements of Film Thickness漆膜厚度测量法ISO 4624Paints and varnishes - Pull-off test for adhesion附着力拉开测试法3.Coating Systems油漆配套Surface PreparationAbrasive blast cleaning to ISO8501-1 Sa21/2 or SSPC SP 6, obtain a sharp表面处理angular surface profile in 50-75 microns.采用磨料喷砂处理至 ISO8501-1 Sa2.5或 SSPC SP6，粗糙度达到Rz

11、=50-75 微米。Coat Name 涂层名称Product NameDFT (microns)产品名称干膜厚度 ( 微米 )Primer 底漆Interseal 670HS200Surface Tolerant Epoxy低表面处理环氧树脂漆Total DFT总干膜厚2004. Surface Preparation表面处理4.1 Steelwork preparation钢结构处理In order to provide surfaces which will ensure optimum paint performance, prior to blastcleaning, weld de